Designing Displays for a Craft Show – Display Boards Part 2

Last time we discussed the importance of understanding your booth and set-up needs before you design your display boards. Now onto designing the actual display boards.

I currently have two different heights of jewelry display boards – a set that is about 18 inches tall and another set that is about 40 inches tall. The boards are designed to be used in two very different shop set-ups. If I am in a small space where I need to stand behind the table and reach over to talk to customers and do transactions, I use the short boards.

When you are designing your boards, consider the board height and the length of your arms. I could have made the boards a little higher, but I wanted to COMFORTABLY be able to reach over them to wait on customers. Comfort becomes an important consideration when you are on your feet for hours at a time. When there are no customers around, the short boards still allow me a clear view of the display and the ability to welcome and interact with customers without standing up. This arrangement also allows me to set another tall board behind me for even more vertical display space when I have a slightly deeper booth.

display board layout

Before we go on to final board design, I need to mention the table that you will be using. When you rent a space at an inside show, it may or may not come with table(s), a tablecloth, a chair, and a trash can. Outside shows normally only rent you a piece of ground and you are responsible for your entire set-up. If it is your own table, you have complete control over the height and appearance of the table (more on that in an upcoming blog). Be sure that you know how tall your table will be when you design your display. If you design the board for a 30 inch high table and wind up using a 36 inch table you may not be able to reach over the display board comfortably.

So what kinds of material can we use to make a display board? Probably the most common material is plywood. It is readily available, easy to cut, flat, and sturdy. So what are the downsides? It can be heavy if the boards are large, the surface must be covered in order to give a finished look, and the plywood can warp.

You can make your boards out of metal sheeting, as long as you stiffen the edges with a frame of metal channel or bond the metal sheet to a sheet of plywood for stability. Using metal sheeting eliminates the need to cover the board and allows you to use magnets to attach items (as long as the sheet of metal is an iron alloy – check to make sure it works with a magnet before you build your board).

I don’t use plastic sheeting for any of my boards. The need for an additional frame, the tendency for plastic to scratch easily, and the fact that some plastics warp in the heat just made it too difficult.

Next Time: Building the Display Boards

 

 

 

Designing Displays for a Craft Show – Display Boards Part 1

Last time we talked about some of the challenges that we can face running a craft booth at an outdoor event. One of the very important issues outside, is how to build display boards that will not blow over in a gusty breeze. Clumsy or careless customers knocking over displays can be an issue at indoor events, too. One of the things that I learned quickly was that if one display board falls over most customers will run for the hills, whether it was their fault or not.

When I started selling jewelry at outdoor craft fairs, I used the small necklace display boards that are often used in mall jewelry shops. But it didn’t take long for me to realize that I needed to make better use of vertical space. “Going up” lets you show more items in the space. From that first outdoor event I learned that my display boards needed to be very sturdy to withstand whatever the weather could throw at me.

Before you build your display boards you need to consider what size they should be, how you will hang your items on the boards, and whether you want to always hang the same things on the same boards. Alternately, you could have more flexibility in terms of board layout. Once you think you understand these facts, then you need to choose the display board materials and what it will be covered with.

Whenever I think of display design, I remember a very wise teacher that I had once in a class on booth design. He basically said “Ladies, don’t ask a male friend to build your displays. We will build it. We will use two by fours and 1″ plywood, it will weigh a ton, and require a large team of sturdy men to set it up.” He then recounted a story where he and some friends used recycled solid antique doors to create a display space for a friend’s paintings. It looked awesome and worked very well. BUT, with each door weighing 80 to 100 pounds and eight doors in the display, it took a small army of sturdy men to set it up and a truck to haul all of pieces.

Consider whether you’ll set up the display by yourself, how far you may need to transport it, and what sort of vehicle you will need to hold all of the pieces and any tools needed to set it up. Most convention center environments have strict regulations about what you are allowed to bring in yourself and what you have to pay someone to haul for you. These contractors are often hired by the convention center and can be quite expensive. Make sure that you investigate what the rules are about you bringing in displays. How far away will you have to park? Will you be allowed to use a dolly or wagon to bring in your displays and products? Most, but not all, outside venues allow you to drive to your booth to do set-up. When you are considering applying for a show, READ the rules first. Most will tell you when you are allowed to set up, and how you can do it. If you have questions, contact someone at the show to make sure that you understand the rules. Violating the terms for set up, especially at large convention centers (even if it’s a small show) can delay your setup significantly.

Next time: More on building display boards and other display issues.

DROID3 TRY3 046

Thinking it Out – So you want to do a Craft Show Outside…

I recently read a jewelry hint newsletter that started something like this, ” I had planned out how to make my booth pretty, but I never realized what can happen if there is a nasty gusty wind.” When I mentioned this to a couple of my friends that I merchant with on a regular basis their response was “What planet does this person live on? Do they sell only at indoor events?” And that made me think that it might be time to write a blog about this topic. Most of the events that I do are outside.

If all you are going to do is sell at indoor events, your product problems are mostly limited to issues of appearance (make it look good), security (keep thieves from taking your stuff), and efficiency (fit as much into a small space while still making it functional). But if you are going to be selling at any kind of outdoor event you MUST consider what you will do if there is weather. And most of the time there will be weather, if not this time, then next time!

Here are the sorts of questions that you need to ask yourself in order to have a successful, weatherproof event.

Rain. If it rains can you protect your product and still be able to sell it? Is your product ruined if it gets wet? If your product is water sensitive, can you package it to make it safe and still have it be attractive to your customers? If your product is placed into a waterproof or water-resistant package, is it removable so that the customer can view it closely, or do you need to have a sample available. Is a sample enough. For instance, a handmade card, where the front of the card is the selling point is easily encased in plastic. A hand painted scarf, where each portion of the scarf is unique has to be in packaging that allows the entire scarf to be easily viewed and then put away again.

Dust. Yes, it does feel like the opposite of rain, but sometimes it can appear, even with rain. It can also turn into mud if there is a source of moisture. If the ground that you are on is covered with grass the amount of dust will be less, but road and foot traffic can sill stir up a surprising amount of dust. The longer an event is, the more likely dust is to be a problem. The grass can be trampled and the sprinklers can`t be run with vendors’ booths in the way. I have a friend who sells handmade soap and lotion bars who has lost product because it became coated with dust at an event. She now wraps her product in plastic for outdoor events. Also be aware of how difficult it will be to remove the dust from your packaging. Some packaging is more difficult to clean than others.

Wind. If the wind starts to blow will it damage your product? Will your product blow away? Will your display fall over?

Heat. Is your product heat sensitive? Will it melt or bend or slump or blurr?

Cold. Will cold make your product freeze, and if it does will it be ruined or break?

Light. Is your product subject to fading from exposure to light?

I hope that these thoughts will help you avoid some of the things that can go wrong in an outside vending environment, and better prepare to deal with the challenges that you may encounter. Planning can eliminate a lot of the drama. Next time we will discuss some display techniques that work well either inside or outside.

Storm then wind then dust then rain.

Storm then wind then dust then rain. (Photo credit: Wikipedia)